Parts & Accessories

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

- Crank Arm Length: 170mm - Interface: Square - Position: Left

• Square taper interface • Only includes left crank

Stages Gen 3 single-sided Power L meter is built onto a non-drive-side Shimano GRX RX-810 crank arm. It's compatible with all Shimano GRX Cranksets. Tour Proven Stages Power has carried riders to three consecutive Tour de France victories, plus many more world and national championships. If you believe racing provides the world's best product-proving ground, then Stages Power is proven as the world's best power meter. Active Temperature Compensation as Standard Equipment Consistency of measurement is the most important feature of a power meter. Stages Power was the first meter to make temperature compensation an automatic process, ensuring accurate readings no matter the environmental conditions. Individual meter calibration for the most accurate results. Stages Power meters are calibrated individually to ensure a +/- 1.5% accuracy level. Individual calibration means that you can trust the data produced by our system. Additional features: - +/- 1.5% accuracy in all conditions - Active temperature compensation - Accelerometer-based cadence measurement - Wirelessly upgradable firmware - LED indicator displays battery level at start up (with no need to connect to an app) and confirms successful zero reset - Updated accelerometer and addition of gyroscope for improved cadence resolution - Upgraded BLE and ANT+ radios offer a 6X improvement of data transmission strength Specifications: - Accuracy: +/- 1.5% - Power meter housing: low-profile design, with robust door interface - Weight: Only adds 15g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) when used as a single-sided meter - Power range (Watts): 0 to 5000 - Cadence range (rpm): 10-220 - Water resistance rating: IPX7 Sizing Options: - Lengths: 170mm, 172.5mm 175mm Compatibility: - This Shimano GRX RX810 Stages Power meter is compatible with all Shimano GRX cranksets. - Frame Compatibility: Most frames - Device Compatibility: ANT+, Bluetooth Smart Ready - Software Compatibility: Stages Link, Training Peaks, Strava, Garmin Training Center, and others

- Octalink bolts include steel washers, JIS includes black plastic caps - HT2 mount bolts (low torque plastic, except XTR-M970 aluminum) are for mounting non-drive arm - Hollow bolts (SH-21504) not recommended for non-treated spindles

- Replacement bolt for DUB cranks

M8 Capless Crank Arm Bolt Kit - For square-taper & Powerspline

CINCH Crank Bolt with Washer

Race Face Crank Spiders allow a quick swap between chainring options on the Race Face CINCH crank system.

Problem Solvers Crank Arm Fixing Bolts - 8mm - Sold as a pair

- 42x30x7mm BB30 cartridge bearings housed in a press-fit, composite sleeve assembly for use with a BB386EVO or BB30 crankset in a BB386EVO or Press-Fit 30 (PF30) frame - Road sets include bearings, shields and a wavy washer - Mountain sets include bearings, shields and a spacer - Choose ceramic or stainless steel options

With the conception of our Cane Creek eeWings Titanium crank set we cut no corners, and our CNC-machined preload assembly is no exception. The Cane Creek Crank Preloader is equipped with an aluminum preload ring, an aluminum inner thread ring, and a titanium 2.5mm hex fastening bolt. We are so proud of this piece of jewelry that we decided to design it to fit onto other 30mm crank spindles from SRAM and Raceface, and 28.99mm SRAM Dub Crank spindles. Lose the plastic preload on your crankset, add peace of mind. - 7075 Aluminum thread ring - 7075 Aluminum preload spacer adjuster - Grade 5 Titanium 2.5mm hex fastening bolt - Fits Raceface 30mm spindles, SRAM 30mm spindles, and SRAM 28.99mm DUB spindles

- Lower slider replacement parts for E-13 chainguides

- Service parts for E-13 chainguides

- Replacement bolt kits for mounting chain guides to ISCG and ISCG-05 frame tabs - Kits include chainline adjustment spacers - 8/12mm button head bolts for single ring steel backplate guide applications - 10/16mm flat head bolts for single ring alloy backplate guide applications

- Adapts ISCG-05 mount chainguide arms to fit flange or lockring style bottom brackets

- Adjustable wearplate with chainring size indicators allow for 28-38T chainring capacity and easy adjustment - Gen 2 Stealth Idler pulley for smooth and quiet operation - 28/30, 32/34, 36/38t direct mount bashguard included - ISCG-05/BB models include ISCG-05 to BB adapter plate - 136g (30t), 159g (34t), 167g (38t) - Range: 28-38t

absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability. - Bolts use a Torx T30 interface for greater reliability - Long bolts are used for the following chainrings: 110 BCD 4-bolt outer and inner road oval, 104 BCD oval 26/28/32t, 64 BCD round 26/28/30t, 94 BCD oval 30/32/34t, all CX round chainrings - Set of 4

absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability. - Bolts use a Torx T30 interface for greater reliability - Long bolts are used for the following chainrings: 110 BCD 5-bolt outer and inner road oval, 130 BCD 5-bolt outer and inner road oval, 104 BCD oval 26/28/32t, 64 BCD round 26/28/30t, 94 BCD oval 30/32/34t, all CX round chainrings - Set of 5

absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability. - Bolts use a Torx T30 interface for greater reliability - Short bolts are used for the following chainrings: 104 BCD oval 34/36t, 104 BCD round 32/34/36/38t, and bashrings - Set of 4

absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability. - Bolts use a Torx T30 interface for greater reliability - Short bolts are used for the following chainrings: 104 BCD oval 34/36t, 104 BCD round 32/34/36/38t, and bashrings - Set of 5

The absoluteBLACK premium crank bolt and bolt cover sets are designed to cover the small step down between chainring and crank arms. - Designed to fit Shimano Dura-Ace 9000 cranks - Includes 4 T30 Torx bolts and 4 bolt covers - Not compatible with absoluteBLACK Sub Compact oval chainrings

The absoluteBLACK premium crank bolt and bolt cover sets are designed to cover the small step down between chainring and crank arms. - Designed to fit Dura-Ace 9100 cranks - Includes 4 T30 Torx bolts and 4 bolt covers - Not compatible with absoluteBLACK Sub Compact oval chainrings

The absoluteBLACK premium crank bolt and bolt cover sets are designed to cover the small step down between chainring and crank arms. - Designed to fit Shimano Ultegra 6800 cranks - Includes 4 T30 Torx bolts and 4 bolt covers - Not compatible with absoluteBLACK Sub Compact oval chainrings

The Taco Bashguard is designed to protect your chainring from obstacles like logs or rocks. It is hidden behind the crank and mounted to ISCG05 tabs that are located around your bottom bracket. It offers great protection for both oval and round chainrings, especially direct mount rings that cannot mount to a standard 4-bolt bashring. The Taco Bashguard fits up to a 32T oval chainring or 34T round one. - The Taco Bashguard can be used with any chainring from 26T-32T oval or 26T-34T round - Box includes taco bashguard (assembled), 6 x 1mm spacers, 3 x 3mm spacers, 3x 16mm stainless bolts, and 1 x 12mm stainless bolt - Weight: 56g

- Bash guard protects chainring from logs, rocks and other trail hazards - Designed and manufactured in the USA from 7075-T6 aluminum alloy - See wolftoothcycling.com for mounting tips - 51g (26-30t)

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with the Race Face Cinch cranksets that have a removable spider

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with SRAM cranksets that have a removable spider

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with Shimano cranksets that have a removable spider

CAMO Spider - Made from Aluminum alloy for light weight - Includes 5 black chainring bolts